Or call our technical support: +31852080825

Available Monday through Friday from 7AM to 3:30PM CET
Please create a ticket before calling and keep the ticket number at hand.
At the moment we are only offering support in English, so we kindly ask you to address your issue in English.
Start a new topic

Tilting while dual extrusion

 I am having a problem with my CreatrHS when I try printing 2 different materials. When both materials are being print, the part will tilt forward and to the right (X+, Y-) As far as I know, this is a new problem, but I haven't tried using both extruders in a while.

I upgraded to the new firmware, and also simplify3d 3.0

Long story short, I noticed this when doing prints with support. I tried making a few calibration pieces like this one:

 



As you can see, it is a block within a block (ABS inside HIPS, but it does the same problem either way). What I get is this:

 



I couldn't get my camera to focus on a piece that small, but the short version is that when I tried printing 2 different materials, the print just tilts to the side. This doesn't happen if I only print 1 material. And as soon as the system goes back to printing only 1 material, it straitens (as you can see the ABS above the HIPS wall is straight)

You can see the interior ABS piece (removed from the HIPS) by itself here:

 


It translates with the outer skirt when printing 2 materials, then goes up straight

As best I can figure, there is some hidden X+, Y- code in the layer change script. It isn't in the Gcode itself (I checked, the X and Y coordinates are the same all the way up). I ran this with both the layer change Gcode populated and empty.

It might have something to do with my calibration offset (X+14.9, Y-0.05) That the code might be referencing or comparing to X+15, Y0. But I can't figure it out.


1 Comment

Dear Trevor what I would suggest is try adjusting the offsets using the steps in the link below:

How to calibrate the offset for your Creatr HS hot ends.


You can use the old firmware version for the next link to reflash the firmware until you find the proper offsets and then implement them in the 2.2 firmware through the M50 command.

Uploading the Creatr HS firmware


It is a bit complicated as you have to use the older version of the firmware but this will let us know is the offsets are indeed the root cause.


Let me know if this works.

Login or Signup to post a comment

User Manual

Quick Start Guide

Installation clips
The following 3 clips will guide you through the installation process of your Creatr. By following these, you will be printing within 30 minutes. First start with unpacking the printer. Clickhere to see how you correctly pick up the printer

Part 1 of 3: Unpacking your Creatr

In this clip, you will be guided through the unpacking of a brand new Creatr. The unboxing along with the location of tie wraps which need to be removed are shown, as well as the process of a connecting the cables to the printer and computer.

Part 2 of 3: Software and configuration

In this clip, we will show you how to install the required software. The first step is to download and install the Arduino software to make it possible for your computer to connect with the printer. The next step is to download and install the Repetier Host Leapfrog software or that controlls your 3D printer. We have tried to make this as simple as possible and also provided direct downloading links per operating system.

SIMPLIFY 3D SOFTWARE
If you are using the new Simplify 3D software you can follow all the steps except for the Repetier-Host Leapfrog installation and using explanation. Simply download the software via the purchase link and before first use a pop-up will appear showing you the Simplify 3D Quick start guide. You can also download the Quick start guide or access it from the software via help –> Quick start guide. The quick start guide will briefly explain the functions of the software so that you can start your first print.

Please select you operating system and follow the descriptions in the movie.

Operating systemWindows

The first step is to download and install the Arduino software to make it possible for your computer to connect with the printer. The next step is to download and install the newest version of the Repetier Host Leapfrog software as shown in the clip. This software allows you to convert your 3D software file [STL for example] to a printable file [G-Code] and allows you to control your printer. The Repetier Host Leapfrog software contains standard Creatr Print Profiles. Just select the extruder, the filament material as well as the color and Repetier will automatically select the ideal print temperature providing you the best print quality possible. There is also a Leapfrog support button implemented in the software. A Mac version will be available soon.

If you have followed the installation procedure, but you can’t control your Leapfrog Creatr and the “6 commands waiting” message in Repetier-Host Leapfrog won’t disappear, you have to install the 2.8.28 drivers. Please see Solution can’t connect 6 commands waiting in Repetier-Host Leapfrog how to do so.

For a more thorough description of Slic3s settings please check this guide!

Windows 8
To install the Arduino drivers on a computer with Windows 8 follow these steps after downloading the Arduino software.

- Save unsaved work and write the instructions down
[your computer will reboot into startup options screen]
- Press the Windows Key and the ‘R’ key simultaneously
- Copy the command inside the brackets
–>[ shutdown.exe /r /o /f /t 00 ] – Select ‘Troubleshoot’
- Select ‘Advanced options’
- Select ‘Startup Settings’
- Select ‘Disable Driver Signature Enforcement’
- Install driver as usual via device manager


Mac

In this clip, we will explain you how you can generate a STL file using Sketchup. We show you what to download and how to export your design in STL.

Part 3 of 3: Making your first print!

In this final clip, the process of creating your first print will be explained. This starts with removing the callibration print that is already on the print bed. How to insert the filament and operate the Repetier Host Leapfrog software is also shown, which should culminate in your first 3D Print on the Creatr!

Google sketchupHow to export STL files from Sketchup

The first step is to download and install the Arduino software to make it possible for your computer to connect with the printer. You will then need to in stall this driver for OSX to recognize the hardware.

The next step is to download the Repetier software as shown in the clip. This software allows you to convert your 3D software file [STL for example] to a printable file [G-Code] and allows you to control your printer. We have developed standard print profiles for the Creatr. Please follow the instructions below to install the print profiles for Mac [not yet included in the video]:

- Download This file
- Go to your Home Folder on Mac and select “Go to Folder” from the Go Menu en type “Library/Application Support/Slic3r/” - Unzip the file you just downloaded and dump the contents in the Slic3r folder, it will replace your existing settings. If you want to keep your current settings as well, take the contents from each folder and put this in the same folder in the Home/Libaray/App../Slic3r folder.

Download instructions by Deepak Dinesh Mehta For a more thorough description of Slic3s settings please check this guide!

Troubleshooting Trees

Filament Guide

ABS
  • Extrude at ~ 225o C.
  • Requires heated bed.
  • Works reasonably well without cooling.
  • Adheres best to polyimide tape.
  • Filament tolerances are usually tighter.
  • Prone to cracking, delamination, and wraping.
  • More flexible.
  • Can be bonded using adhesives or solvents(Acetone or MEK).
  • Fumes are unpleasent in enclosed areas.
  • Oil Based.
PLA
  • Extrude at ~ 180-225o C.
  • Benefits from heated bed.
  • Benefits greatly from cooling while printing.
  • Adheres well to a variety of surfaces.
  • Finer feature detail possible on a well calibrated machine.
  • Prone to curling of corners and overhangs.
  • More brittle.
  • Can be bonded using adhesives.
  • More pleasant smell when extruded.
  • Plant Based.

Demo Print Downloads

Drivers Downloads

Software Downloads

Firmware Downloads

Please request a firmware download via the Ticket System

Creatr Video Library